15815509278
取消

0201ZD103KAT

  • 0201ZD103KAT
  • 0201ZD103KAT
0201ZD103KAT
UNKNOWN
-
YES
24
• General Purpose Dielectric for Ceramic Capacitors
• EIA Class II Dielectric
• Temperature variation of capacitance is within ±15%
from -55°C to +85°C
• Well suited for decoupling and filtering applications
• Available in High Capacitance values (up to 100μF)
X5R Dielectric
General Specifications
PART NUMBER (see page 2 for complete part number explanation)
GENERAL DESCRIPTION
% Capacitance
-60 -40
-20 0 +20 +40 +60 +80
Temperature °C
Temperature Coefficient
20
15
10
5
0
-5
-10
-15
-20
TYPICAL ELECTRICAL CHARACTERISTICS
Insulation Resistance (Ohm-Farads)
1,000
10,000
100
0
Insulation Resistance vs Temperature
0
20
120
40 60 80
Temperature °C
100
1210
Size
(L" x W")
4
Voltage
4 = 4V
6 = 6.3V
Z = 10V
Y = 16V
3 = 25V
D = 35V
5 = 50V
D
Dielectric
D = X5R
107
Capacitance
Code (In pF)
2 Sig. Digits +
Number of
Zeros
M
Capacitance
Tolerance
K = ±10%
M = ±20%
A
Failure
Rate
A = N/A
T
Terminations
T = Plated Ni
and Sn
2
Packaging
2 = 7" Reel
4 = 13" Reel
7 = Bulk Cass.
9 = Bulk
A
Special
Code
A = Std.
NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers.
Contact factory for non-specified capacitance values.
25
X5R Dielectric
Specifications and Test Methods
Parameter/Test X5R Specification Limits Measuring Conditions
Operating Temperature Range -55ºC to +85ºC Temperature Cycle Chamber
Capacitance Within specified tolerance
≤ 2.5% for ≥ 50V DC rating Freq.: 1.0 kHz ± 10%
Dissipation Factor
≤ 3.0% for 25V DC rating Voltage: 1.0Vrms ± .2V
≤ 12.5% Max. for 16V DC rating and lower For Cap > 10 μF, 0.5Vrms @ 120Hz
Contact Factory for DF by PN
Insulation Resistance
10,000MΩ or 500MΩ - μF, Charge device with rated voltage for
whichever is less 120 ± 5 secs @ room temp/humidity
Charge device with 300% of rated voltage for
Dielectric Strength No breakdown or visual defects 1-5 seconds, w/charge and discharge current
limited to 50 mA (max)
Appearance No defects Deflection: 2mm
Capacitance Test Time: 30 seconds
Resistance to Variation
≤ ±12%
Flexure Dissipation
Meets Initial Values (As Above)
Stresses Factor
Insulation
≥ Initial Value x 0.3
Resistance
Solderability
≥ 95% of each terminal should be covered Dip device in eutectic solder at 230 ± 5ºC
with fresh solder for 5.0 ± 0.5 seconds
Appearance No defects, <25% leaching of either end terminal
Capacitance
Variation
≤ ±7.5%
Dip device in eutectic solder at 260ºC for 60
Dissipation
Meets Initial Values (As Above)
seconds. Store at room temperature for 24 ± 2
Resistance to
Factor
hours before measuring electrical properties.
Solder Heat
Insulation
Meets Initial Values (As Above)
Resistance
Dielectric
Meets Initial Values (As Above)
Strength
Appearance No visual defects Step 1: -55ºC ± 2º 30 ± 3 minutes
Capacitance
Variation
≤ ±7.5% Step 2: Room Temp ≤ 3 minutes
Dissipation
Meets Initial Values (As Above) Step 3: +85ºC ± 2º 30 ± 3 minutes
Thermal
Factor
Shock
Insulation
Meets Initial Values (As Above) Step 4: Room Temp ≤ 3 minutes
Resistance
Dielectric
Meets Initial Values (As Above)
Repeat for 5 cycles and measure after
Strength 24 ± 2 hours at room temperature
Appearance No visual defects
Capacitance
Variation
≤ ±12.5%
Dissipation
≤ Initial Value x 2.0 (See Above)
Load Life Factor
Insulation
≥ Initial Value x 0.3 (See Above)
Resistance
Dielectric
Meets Initial Values (As Above)
Strength
Appearance No visual defects
Capacitance
Variation
≤ ±12.5%
Load Dissipation
≤ Initial Value x 2.0 (See Above)
Humidity Factor
Insulation
≥ Initial Value x 0.3 (See Above)
Resistance
Dielectric
Meets Initial Values (As Above)
Strength
Charge device with 1.5X rated voltage in
test chamber set at 85ºC ± 2ºC for 1000 hours
(+48, -0). Note: Contact factory for *optional
specification part numbers that are tested at
< 1.5X rated voltage.
Remove from test chamber and stabilize
at room temperature for 24 ± 2 hours
before measuring.
Store in a test chamber set at 85ºC ± 2ºC/
85% ± 5% relative humidity for 1000 hours
(+48, -0) with rated voltage applied.
Remove from chamber and stabilize at
room temperature and humidity for
24 ± 2 hours before measuring.
1mm/sec
90 mm
26
X5R Dielectric
Capacitance Range
PREFERRED SIZES ARE SHADED
SIZE 01005 0201 0402 0603 0805 1206 1210 1812
Soldering Reflow Only Reflow Only Reflow/Wave Reflow/Wave Reflow/Wave Reflow/Wave Reflow Only Reflow Only
Packaging All Paper All Paper All Paper All Paper Paper/Embossed Paper/Embossed Paper/Embossed All Embossed
(L) Length
mm 0.40 ± 0.02 0.60 ± 0.03 1.00 ± 0.10 1.60 ± 0.15 2.01 ± 0.20 3.20 ± 0.20 3.20 ± 0.20 4.50 ± 0.30
(in.) (0.016 ± 0.0008) (0.024 ± 0.001) (0.040 ± 0.004) (0.063 ± 0.006) (0.079 ± 0.008) (0.126 ± 0.008) (0.126 ± 0.008) (0.177 ± 0.012)
(W) Width
mm 0.20 ± 0.02 0.30 ± 0.03 0.50 ± 0.10 0.81 ± 0.15 1.25 ± 0.20 1.60 ± 0.20 2.50 ± 0.20 3.20 ± 0.20
(in.) (0.008 ± 0.0008) (0.011 ± 0.001) (0.020 ± 0.004) (0.032 ± 0.006) (0.049 ± 0.008) (0.063 ± 0.008) (0.098 ± 0.008) (0.126 ± 0.008)
(t) Terminal
mm 0.10 ± 0.04 0.15 ± 0.05 0.25 ± 0.15 0.35 ± 0.15 0.50 ± 0.25 0.50 ± 0.25 0.50 ± 0.25 0.61 ± 0.36
(in.) (0.004 ± 0.016) (0.006 ± 0.002) (0.010 ± 0.006) (0.014 ± 0.006) (0.020 ± 0.010) (0.020 ± 0.010) (0.020 ± 0.010) (0.024 ± 0.014)
WVDC 6.3 4 6.3 10 16 25 4 6.3 10 16 25 50 4 6.3 10 16 25 35 50 6.3 10 16 25 35 50 6.3 10 16 25 35 50 4 6.3 10 16 25 35 50 6.3 10 25 50
Cap 100 A
(pF) 150 A
220 A C
330 A C
470 A C
680 A C
1000 B A A C
1500 A C
2200 A A C
3300 A C
4700 A C G
6800 A C G
Cap 0.010 B A C G
(µF) 0.015 C G G G
0.022 A
*
CC GGG N
0.033 C G G G N
0.047 A
*
CC GGG N
0.068 C G G N
0.10 A
*
CCC G G N N
0.15 GNN
0.22 A
*
A
*
C
*
GG NN Q
0.33 GG N
0.47 C
*
C
*
GNQQ X
0.68 GN
1.0 C
*
C
*
C
*
GGGJ
*
NN P* QQ XXX
1.5
2.2 C
*
C
*
G
*
G
*
J
*
J
*
NNN QQ Z X
3.3 J
*
J
*
J
*
J
*
NN QQ
4.7 E
*
J
*
J
*
J
*
NNN
*
N* QQQQ QZ
10 KJ
*
N
*
N
*
N
**
QQQQ
*
XZZ
*
Z
22 N*
*
Q
*
Q
*
Q
*
ZZZZ
*
47 *Q
*
Z
*
100 Z
*
Z*
WVDC 4 6.3 10 16 25 4 6.3 10 16 25 50 4 6.3 10 16 25 35 50 6.3 10 16 25 35 50 6.3 10 16 25 35 50 4 6.3 10 16 25 35 50 6.3 10 25 50
SIZE 01005 0201 0402 0603 0805 1206 1210 1812
= Under Development
= *Optional Specifications Contact factory
L
W
T
t
NOTE: Contact factory for non-specified capacitance values
Letter ABCEGJKMNPQXYZ
Max. 0.33 0.22 0.56 0.71 0.90 0.94 1.02 1.27 1.40 1.52 1.78 2.29 2.54 2.79
Thickness (0.013) (0.009) (0.022) (0.028) (0.035) (0.037) (0.040) (0.050) (0.055) (0.060) (0.070) (0.090) (0.100) (0.110)
PAPER EMBOSSED

Analog Devices Inc.
IC OVERVOLT PROT CTRLR SOT23-6
Texas Instruments
IC ASYNC STEREO CODEC 28-TSSOP
Nuvoton Technology Corporation of America
IC VOICEBAND CODEC 3V 1CH 20SSOP
Texas Instruments
IC OPAMP JFET 4 CIRCUIT 14SOIC
Nuvoton Technology Corporation of America
IC MCU 32BIT 256KB FLASH 48LQFP
Nuvoton Technology Corporation of America
IC MCU 32BIT 128KB FLASH 64LQFP
Nuvoton Technology Corporation of America
IC MCU 32BIT 64KB FLASH 48QFN
Nuvoton Technology Corporation of America
IC MCU 8BIT 32KB FLASH 28TSSOP
Nuvoton Technology Corporation of America
IC MCU 8BIT 16KB FLASH 20TSSOP
Nuvoton Technology Corporation of America
IC MCU 8BIT 32KB FLASH 33QFN
Nuvoton Technology Corporation of America
IC MCU 8BIT 8KB FLASH 10MSOP
Pulse Electronics Network
FIXED IND 22NH 700MA 190MOHM SMD
Molex
Power Outlet Strips 3290 W/(2)L5-15 &amp; (2)5-20 SPLT WIRED
API Delevan Inc.
FIXED IND 47NH 600MA 310MOHM SMD
Connector Accessories Actuating Handle Kit Thermoplastic
Military Spec
RESISTORS, SHUNT, Current Rating:15A, Accuracy %:1%, Opera
Littelfuse
FUSE BRD MNT 4A 125VAC/VDC AXIAL
GRAYHILL
SWIT ROTARY DP 2 SHAFT SLDR LUG 0.25A 115VAC 28VDC - Bulk
关闭
Inquiry
captcha

15815509278

295144934@qq.com
0